KISS documentation
  • Welcome / Willkommen
  • English - KISS docu
    • KISS ESC 24A
      • Technical data
      • ESC wiring and connections
      • FW revisions
    • KISS ESC 25A
      • Technical data
      • ESC wiring and connections
      • FW revisions
    • KISS ESC 25A 4in1
      • Technical data
      • ESC wiring and connections
      • FW revisions
    • KISS ESC 32A
      • Technical data
      • ESC wiring and connections
      • FW revisions
    • KISS ESC common info
      • KISS ESC - serial receiver
      • KISS ESC - calibration & 3D mode
      • KISS ESC - FW update
      • KISS ESC - CLI
      • KISS ESC - FAQ
      • KISS ESC - safety warnings
      • KISS ESC - sinHybrid
      • KISS ESC - Dshot
    • KISS FC v1
    • KISS CC
    • KISS FC v2
    • KISS FC common info
  • Deutsch - KISS Doku
    • KISS ESC 24A
    • KISS ESC 25A
      • Technische Daten
      • ESC Anschlussbelegung
      • FW Revisionen
    • KISS ESC 25A 4-in-1
      • Technische Daten
      • ESC Anschlussbelegung
      • FW Revisionen
    • KISS ESC 32A
    • KISS ESC generelle Informationen
      • KISS ESC - serielle Empfänger
      • KISS ESC - Kalibrierung & 3D Modus
      • KISS ESC - FW update
      • KISS ESC - CLI
      • KISS ESC - häufige Fragen
      • KISS ESC - Sicherheitsinformationen
      • KISS ESC - sinHybrid
      • KISS ESC - Dshot
Powered by GitBook
On this page
  • FrSky SBUS und S-Port
  • Graupner SumD and HOTT
  • Multiplex SRXL and Sensorbus
  • TBS Crossfire
  1. Deutsch - KISS Doku
  2. KISS ESC generelle Informationen

KISS ESC - serielle Empfänger

Beschreibt wie die KISS ESC direkt an einen seriellen Empfängerausgang (SBUS, Graupner SUMD, Multiplex SRXL oder TBS CRSF Empfänger).

PreviousKISS ESC generelle InformationenNextKISS ESC - Kalibrierung & 3D Modus

Last updated 6 years ago

Diese Funktion wird nur von KISS ESC 25A sowie KISS ESC 32A unterstützt!

Die KISS ESC unterstützen den direkten Anschluss an einen seriellen Empfänger. Das Eingangssignal wird automatisch detektiert. Da die ESC keine 5V versorgung an den Empfänger liefern muss dieser seperat versorgt werden!

Die Ausgabe eines Telemetrieprotokolles is bei PWM Signal input separat einstellbar. Weitere Informationen dazu findest du in der Beschreibung zum .

Achtung Baustelle ;) - die Umstellung auf Deutsch erfolgt in den kommenden Tagen!

FrSky SBUS und S-Port

Connect the Sbus Output to Sig. | RX pin. And if you need Telemetry connect S-Port to TLM | TX. If a valid Sbus signal is detected, S-Port becomes active automatically.

The ESC uses Sbus channel 0 as default throttle channel. It can be changed in the . For S-Port its default senor adress is 27. It can be changed in the CLI interface.

Available telemetry:

- Voltage (Volt)

- Current (Ampere)

- Consumption (mA/h) - Temperature (°C)

- RpM (Default for 14 Magnetpole Motor, confugurable in CLI)

Graupner SumD and HOTT

Connect the SumD Output to Sig. | RX pin. And if you need Telemetry, HOTT to TLM | TX. If a valid SumD signal is detected, HOTT gets automatically active.

The ESC uses as default throttle channel SumD channel 0. it can be changed in .

In the HOTT telemetry it will be found as Electricl Air Module.

Available telemetry:

- Voltage (Volt)

- Current (Ampere)

- Consumption (mA/h) - Temperature (°C)

- RpM (Default for 14 Magnetpole Motor, confugurable in CLI)

Multiplex SRXL and Sensorbus

Connect the SRXL Output to Sig. | RX pin. And if you need Telemetry, Sensorbus to TLM | TX. If a valid SRXL signal is detected, Sensorbus gets automatically active.

It uses Sensorbus ID 2-6. configurable in CLI

Available telemetry:

- Voltage (Volt)

- Current (Ampere)

- Consumption (mA/h) - Temperature (°C)

- RpM (Default for 14 Magnetpole Motor, confugurable in CLI)

TBS Crossfire

Connect the CRSF TX Output to Sig. | RX pin. And if you need Telemetry, CRSF RX to TLM | TX. The used throttle channel is CRSF channel 0

Available telemetry:

- Voltage (Volt)

- Current (Ampere)

- Consumption (mA/h)

The ESC uses as default throttle channel SRXL channel 3. it can be changed in .

Kommandozeilen Interface - CLI
CLI interface
CLI interface
CLI interface